|Varenr.||Farge||Mod.||Vol.||Info||Lager||Pris inkl. mva|
|402||Hvit||402||100 g||Les mer||På lager: 20+||189,-|
|402A||Hvit||402A||500 g||Les mer||På lager: 5||899,-|
Et spesialformulert fyllstoff for reparasjon av sår og skader på glassfiber/polyester. Egnet for fylling og liming av mindre skader i overflaten.For reparasjoner på glassfiber, tilsett ca. 25 % med fyllstoff 402 i forhold til epoksyblandingens totale vekt.Dette fyllstoffet består av små tynne glassfibertråder på opp til 6 mm. Disse trådene vil være med på å armere epoxyfyllingen slik at reparasjonen blir ekstra sterk.
Bland WEST SYSTEM Resin og Herder godt sammen i riktig blandingsforhold. Tilsett deretter fyllstoffet gradvis til du får ønsket konsistens på blandingen. Ved en tilsetting på ca 20-25 % av 402 vil man få en passe tykk epoxypasta som kan påføres reparasjonsstedet.
WEST SYSTEM® 402 MILLED GLASS FIBRE BLEND (Type: Blended adhesive filler. Product No: 402)
What is it? WEST SYSTEM 402 Milled Glass Fibre Blend is a mix of individual strands of chopped glass evenly dispersed in a powder base made up of other fillers. This combination creates high-density filler that is perfect for semi-structural repairs. No other manufacturer is produces this type of gap filler and it has proved very effective in GRP repairs.
Used for? Mainly for filling small holes in fibreglass laminates, as any repairs are incredibly strong. A WEST SYSTEM epoxy/402 Filler mix can also be used to build up platforms or other supportive shapes, such as the bulb around a new bow thruster tunnel, or to fill voids under a davit base. The mix can also be used to fill impact damage to centreboards and rudder blades where long-term strength is needed.
Mixing ratio: The WEST SYSTEM 402 Filler should be added at a ratio of 25% by weight to the mixed WEST SYSTEM epoxy. The result will be a thick paste that can be manipulated with a brush, using a stippling motion, or with a palette knife. Repairs can also be held in place with PVC tape or peel ply until they have cured.
Hamish’s Tip’s for the WEST SYSTEM 402 Filler:
Keep it workable.
“The temptation with any epoxy mix is to make enough for the job, but a large amount of filler can exotherm (create its own heat through a chemical reaction) and cure much faster than expected. Only mix up enough material that you can use in 10 minutes or so, and spread it out in the pot of on a roller tray if possible to increase the surface area. This will slow down the exothermic reaction.”
Tidy up with fine filler:
“Because of its mat-like composition, a visible repair may seem a little uneven, so a good tip is to finish off the repair with fine surface filler before overpainting.”
Watch out for needles!
“The thin fibreglass strands that give the additive its strength can also protrude from the cured mix and catch your hands, so we always recommend placing peel ply over the top of the mix as it cures. The peel ply will knock the strands flat and once peeled away will reveal a smooth surface for further build up.”
Typical damage that a mix of WEST SYSTEM epoxy/402 Filler is ideal for mending – by bridging the hole, especally when access from behind the damage is difficult.
The hole is ground back to form a concave receptor.
The repair is then faired with WEST SYSTEM epoxy/409 Microsphere Filler mix. The material is sanded flat when cured.
The final stage is to finish with an epoxy primer and paint system, or a colour-matched gel coat so the repair literally disappears.